Now that you have the conceptual design for your deck, and you plan on doing this on your own, it is time to develop the structural elements and material specifications. No matter if you complete the project yourself or hire a contractor, this exercise will help you to get an understanding of the details of your deck. These specifications will be a part of the Construction Document you will either take to the building department for a permit, use to get bids on the project or use to build the deck yourself.
You might have already begun thinking about the construction details and possibly have a pretty good idea of the components that make up a deck or have some good questions. And, unless you have special conditions, we will answer most of those questions here. Special conditions include steep slopes, unstable soil and specific building codes. If you are unsure where your project fits, check with a contractor or the building department.
After you complete this tutorial, you will have a better idea whether to doityourself or hire a contractor. So, grab your sketches and here we go.


Skill Level & Time to Complete




•
Beginner  3 to 4 hours 

•
Intermediate  2 to 3 hours 

• Advanced  1 to 2 hours 

 Saving money by scrimping on materials or crowding the design tables will come back on you when the deck begins to age. Pay more now to save in the future. 

 If you put this project out to bid, the estimates will be more "applesforapples" if the contractors have a detailed plan to bid from. The Construction Document you are creating here will help make this possible. 

 Determine the direction the deck boards will run, this will influence the layout of the joists and girders. Most deck boards run parallel with the long dimension of the deck. 

 Print out the Deck Spec and Materials list, which you can fill out in the following steps. 

6. 
Estimate girders: The girders are 4x6's on this deck and will "run" the same direction as the deck boards. This plan calls for girders spaced 6 feet 8 inches apart and supported by piers every 6 feet (check applicable joist span tables). Girders should be supported on three piers where possiblethis will make the minimum desirable length 12 feet, remember the piers are 6 feet apart. Therefore the best girder lengths are multiples of six, and the longest manageable length will be 18 feet. Also, the girders must be supported at the ends on piers.
For our deck there will be three "rows" of girders, each 30 feet long, for a total of 90 linear feet of 4x6. For this estimate add 10 % for waste, be sure to check for availability of the required lengths. 


7. 
Estimate joists: The joists are spaced 16 inch on center and will run perpendicular to the girders and deck boards. To figure the number of joists, convert the length of the deck to inches (a 30 foot deck is 30 x 12 = 360 inches) and divide that by the 16inch spacing (360 / 16 = 22.5) and round up (22.5 becomes 23.) Add 1 to that to figure the total number of joists. This deck will require 24 joists spaced at 16 inches on center. Multiply this number by the deck width (20 feet) to estimate the total linear feet of 2x6 joists, 460 linear feet plus 10% (46) equals 510 (round up.) 


8. 
Estimate deck boards: This deck will have 2 x 6 decking, a 2 x 6 is usually 5 ½ inches instead of 6 as the name implies. So a standard 2 x 6 one foot long (a linear foot of 2x6) will cover .46 square feet.
Our deck is 600 square feet (20 x 30) so there will be 600 / .46 = 1,304 linear feet of deck boards. Be sure to include a 10% waste factor (134 feet) and the total is 1434 linear feet of 2 x 6.



9. 
Estimate stairs: This deck is 30 inches above the ground and has one set of stairs 36 inches wide. To figure the actual number of steps, divide 30 inches by 6 inches5 steps, the last one being the deck itself. Height of deck above ground divided by 6 equal the number of steps.
To figure stringer length, multiply the number of steps by 16 inches for each stringer. Our deck has five steps times 16 inches80 inches6 feet 8 inches. Stairs up to 36 inches wide have two stringers, and stairs over 36 inches have three stringers up to 6 feet for the stringers. The steps (the steps are 2x6 the same as the deck) have two 2x6's, times the width of the stairs. In this case, each step will have two 2x6's by 36 inches. Five steps will require 10 x 36 inch or 30 lineal feet of material. Add this to the deck material order. 


10. 
Estimate railings: This deck has guard railings on two sides and hand railings on the stairs. Measure the open sides of the deck and add the stair rail. Get the stair rail length from the stair stringer length in step nine.
Calculate one 8foot 4x4 (post) for each 6 feet of rail, 2 feet of 2x4 (top and bottom rail) for each 1 foot of rail and 2.2 1x2 (baluster) for each foot of rail.
There are three parts of the railing, the posts, the top and bottom rail and the balusters. 


11. 
Hardware and fasteners: You will need galvanized nails, metal connectors and bolts to connect your deck parts. Figure one pound of 16d galvanized nails for each 10 square feet of deck, use the double hot dipped galvanized kind.
Each joist will require two joist hangars. Each post should have a post cap to connect it to the girder it supports. Figure one pound of galvanized nails for each 10 metal connectors. The manufacturer will specify the size of nail for their product. Allow one bolt per foot of ledger, be sure to measure the length necessary to "run" the bolt through the wall framing and install a nut and washer on the other side. 


Copyright©
20012006 Easy2.com, Inc. All rights reserved.
